View IWD505_53001.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

IWD SERIES - DUAL OUTPUT, 10 WATT
DESCRIPTION IWD dual output DC/DC converters offer excellent regulation and isolation in an industry-standard package. Available in 5V and 12V input versions, the IWD is perfect for industrial, datacom, or telecom applications. The IWD features short-circuit protection and 500 VDC isolation. Please see the IWS and IAS series for single output applications. FEATURES * * * * Industry Standard Package Industry Standard Pinout 85C Case Operation Short Circuit Protection * * * * * 5V and 12V Inputs Input Pi Filter 6-Sided Shielding Wide Input Voltage 500V Isolation
Efficiency vs. Load (5V Input)
90 85 80
EFFICIENCY %
75 70 65 60 EFF. IWD505
EFF. IWD512
TECHNICAL SPECIFICATIONS
Input Voltage Range 5 VDC Nominal 12 VDC Nominal Reflected Ripple Reverse Input Current Output Setpoint Accuracy Line Regulation Vin Min. - Vin Max., Iout Rated Load Regulation Iout Min. - Iout Max., Vin Nom. Minimum Output Current Dynamic Regulation, Loadstep Pk Deviation Settling Time Temperature Coefficient Ripple and Noise, 20 MHz BW Short Circuit Protection 1 Current Limit General Switching Frequency Isolation Input - Output Isolation Resistance - Input to Output Standard Case Operating Range Storage Range Humidity Max., Non-Condensing Vibration, 3 Axes, 5 min each Safety Weight (approx.) REV. 08/30/01 300 kHz 500 VDC 109 Ohms -25 to +85C -40 to +125C 95% 5 g, 10 - 55 Hz UL, cUL, TUV 1.4 oz 1% 1.0% Vout 1.0% Vout 10 % Iout Rated 25% Iout 1% Vout 500 s 0.02%/C 1% Vout nom. Hiccup 130% 4.5 - 9 VDC 9 - 18 VDC 20% Iin Max. 100% Iin Max.
55 50 10 20 30 40 50 60 70 80 90 100
LOAD %
Efficiency vs. Load (12V Input)
90 85 80
EFFICIENCY %
75 70 65 60 55 10 20 30 40 50 60 70 80 90 100
LOAD %
EFF. IWD1209
EFF. IWD1212
Notes
1 Converter will auto-restart once fault has been removed. Specifications typically at 25C, normal line, and full load, unless otherwise stated. Soldering Conditions: I/O pins, 260C, ten seconds; fully compatible with commercial wave-soldering equipment. Safety: Agency approvals may vary from model to model. Please consult factory for specific model information.
1
IWD SERIES - DUAL OUTPUT, 10 WATT
MODELS - (See the last page of section for options.)
MODEL INPUT VOLTAGE (VOLTS) INPUT VOLTAGE RANGE (VOLTS) MAXIMUM INPUT CURRENT (AMPS)* OUTPUT VOLTAGE (VOLTS) RATED OUTPUT CURRENT (AMPS) RIPPLE & NOISE pk-pk (mV) TYPICAL EFFICIENCY**
IWD505 IWD512 IWD515 IWD1205 IWD1212 IWD1215
NOTES:
5 5 5 12 12 12
4.65 - 5.50 4.65 - 5.50 4.65 - 5.50 10.90 - 13.20 10.90 - 13.20 10.90 - 13.20
3.20 3.20 3.20 1.55 1.55 1.55
5 12 15 5 12 15
1.000 0.500 0.375 1.000 0.500 0.375
50 120 150 50 120 150
82% 80% 82% 80% 84% 82%
* Maximum input current at minimum input voltage, maximum rated output power. ** At nominal Vin, rated output.
MECHANICAL DRAWING
1.00" (25.4mm)
0.18" MIN. (4.6mm)
0
3
4
5 DIA 0.040" (1.0mm)
2.00" (50.8mm) 0.800"(20.3mm) 1 2
1.40"(35.6mm) 0.800" 0 (20.3mm) 0.300" -0.10" (7.6mm) 0.500" (12.7mm) (-2.5mm) 0.400" (10.2mm) 0.40" (10.2mm)
BOTTOM VIEW
Tolerances Thermal Impedance Natural convection 100 LFM 200 LFM 300 LFM 400 LFM 15.4 C/W 12.2 C/W 9.3 C/W 7.4 C/W 6.4 C/W Pin 1 2 3 4 5 Function +Vin -Vin + Vout Common - Vout Inches: .XX 0.040 .XXX .010 Pin: 0.002 Case: + 0.04, - 0.00 (Millimeters) .X 1.0 .XX 0.25
0.05
Note: Thermal impedance data is dependent on many environmental factors. The exact thermal performance should be validated for specific application.
+ 1.0, - 0.0
(Tolerances as listed unless otherwise specified.)
2
OPTIONS
When ordering equipment options, use the following suffix information. Select the option(s) that you prefer and add them to the model number. Example ordering options are located below the options table.
Negative Logic
OPTION SUFFIX
N T
Lucent-Compatible Trim Terminal Strip Trim Enable Trim and Enable Current Share Headerless
PIN LENGTH AND HEATSINK OPTIONS
TS 1 2 3 4 Y 8 9 1H 1V 2H 2V 3H 3V
HAS, HBD, HBS, HES, HLS, LES, QBS, QES, QLS, TES, TQD HAS, HBD, HBS, HES, HLS, QBS, QES, QLS XWS, XWD, XWT IAS, LES IAD, IAS, LES, SMS IAS, LES SMS Encapsulated EWS, IWS, OWS All Units (Except SMS) All Units (Except SMS) All Units (Except DIP, HLS, HLD, QLS, SIP, SM, TLD, and TKD Packages) All Units (Except DIP, HLS, HLD, QLS, SIP, SM, TLD, and TKD Packages) All Units (Except DIP, HLS, HLD, QLS, SIP, SM, TLD, and TKD Packages) All Units (Except DIP, HLS, HLD, QLS, SIP, SM, TLD, and TKD Packages) All Units (Except DIP, HLS, HLD, QLS, SIP, SM, TLD, and TKD Packages) All Units (Except DIP, HLS, HLD, QLS, SIP, SM, TLD, and TKD Packages)
APPLICABLE SERIES
TTL Low Turns Module ON TTL High Turns Module OFF
REMARKS
0.110 (2.8mm) Pin Length 0.150 (3.8mm) Pin Length 0.24 (6.1mm) Horizontal Heatsink 0.24 (6.1mm) Vertical Heatsink 0.45 (11.4mm) Horizontal Heatsink 0.45 (11.4mm) Vertical Heatsink 0.95 (24.1mm) Horizontal Heatsink 0.95 (24.1mm) Vertical Heatsink
Standard Pin Length is 0.180 (4.6mm) Includes Thermal Pad Includes Thermal Pad Includes Thermal Pad Includes Thermal Pad Includes Thermal Pad Includes Thermal Pad
Example Options: HBS050ZG-ANT3V = HBS050ZG-A with negative logic, Lucent-compatible trim, and 0.95 vertical heatsink. LES015YJ-3N = LES015YJ with optional trim and enable, negative logic. QBS066ZG-AT8 = QBS066ZG-A with Lucent compatible trim and 0.110 pin length.
NUCLEAR AND MEDICAL APPLICATIONS Power-One products are not authorized for use as critical components in life support systems, equipment used in hazardous environments, or nuclear control systems without the express written consent of the President of Power-One, Inc. TECHNICAL REVISIONS The appearance of products, including safety agency certifications pictured on labels, may change depending on the date manufactured. Specifications are subject to change without notice.
3

▲Up To Search▲

Price & Availability of IWD505

	To Download IWD505 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .